Instructions
Product Instructions
IMPORTANT! Read Directions Before Use
Metal Cleaner Standard is the first step to almost all projects. Deep cleans the surface all the way down through the pores of metal, glass, gel coated fiberglass, and clear coat paint. As with all products, initially start with a small discrete area. A multitude of applicators can be used depending on the size of job and scratch potential of surface. Example; terry cloth, microfiber towel, indoor outdoor carpet patch, or a long handle wash brush. We like microfiber towels as they eliminate the possibility of scratching, thus providing the best finish available. Quickly soaking your applicator in water then ringing it out assist in the liquid cleaner not rolling off your applicator. Our unique fluoride cleaner works by time, not friction. Evenly work the cleaner over the surface and let it suck the grime out of the pores. Reapplying allowing additional flash time or HP cleaner may be necessary for objects that are highly corroded. If cleaning only, rinse with water and wipe dry with a clean rag.
Metal Cleaner High Performance is used when rust, mildew, acid stains, heat burns, or hard water mineral spots are present on metal or glass . Also used to clean aluminum and stainless steel. It is exactly 20 percent stronger than our Standard and can be diluted in water for large applications. For large aluminum trailers start by pouring 16 oz of HP cleaner in a 5 gal. bucket and add about 2 gallons of water. This may be enough to do the whole trailer but if not you can make additional solution. For smaller trailers start with half of this formula . Depending on how dirty the trailer is, you may have to increase the strength some. Allowing time for the cleaner to work is the key. First wet the sides of the trailer down with a water hose. Then apply the cleaner with a long handle RV brush . When dipping the brush, let it drip some back into the bucket so that you do not waste it. A little goes a long way. NOTE: Start at the bottom and work your way up so that the cleaner does not streak . Do this in 10 foot sections so that you can control the amount of time the solution stays on the surface. Let it dwell on the surface for a couple of minutes, then rinse . For deep stains on aluminum, you may want to use the carpet pads ( included in your order) with the solution to try and remove them. This cleaner will not hurt painted surfaces or decals if directions are followed by rinsing within a couple of minutes. It prepares painted surfaces for the Top Wax application. Do not let it dwell on glass windows more than a couple of minutes. Use extreme caution when handling. (Contains Hydrogen fluoride CAS No.: 7664-39-3 DO NOT allow exposure to hydrogen fluoride through inhalation, ingestion, and eye or skin contact. Antidote is Milk of Magnesia. Wear heavy rubber gloves and eye protection when handling this product.)
(see product use instructions for Metal Cleaner Standard)
Metal Wax is a non-abrasive non-flammable polishing gel used on all metal surfaces. It includes no grinding components. After prepping surface with our Metal Cleaner, immediately apply the gel with a microfiber towel or applicator and watch the impurities come out. Unlike traditional abrasive rogue based polishing compounds, buffers are not necessary. After rubbing the gel deep into the cleaned surface, wipe off excess with a clean terry or microfiber towel. Fold the towel, exposing the clean side, to remove remainder of gel. You must pick-up all black residues. You have now created an exceptional polished finish accompanied by weatherproofing additives. Metal Wax application and removal can be repeated as desired for an increased mirror like finish, or, spray on our new Quick Shine metal polish. Kitchen use: remove with soap/water.
(yellow)
Metal Wax Polish (yellow) may be used on very dirty or black streaked painted surfaces. It will remove the dirt and surface marks and scratches. Apply this with an applicator or terry cloth towel. Polish to the point that the paint looks clean and then simply wash off the residue with your metal cleaner solution or soap and water. The finish, once dry will look dull. Top Wax is then applied to a dry surface for the final protection and shine. It goes on easy and wipes off with very little buffing required.
Always wear rubber gloves and face and eye protection when using the cleaner.
Note: Polishing mill finished aluminum siding can be a never ending job. It is best to just use the cleaner for this type of finish. But if you desire a truly protected finish, the Metal Wax Polish can be applied and buffed by hand. Always use Metal Wax on stainless steel, diamond plate, aluminum wheels and aluminum fenders for a brilliant shine. It provides a lasting protection . Call or e-mail us for direction if you have any questions.
Quick Shine is a liquid metal polish. Comes with a convenient sprayer in 16 ounce size. Simply spray on, wipe off, it’s polished! Can be used as a clarifier for ultimate shine performance after prepping surface with Metal Cleaner and Metal Wax. Also, a great maintenance tool to revive a Metal Wax polish. Superb for small areas where polishing gel would be too thick. Also great for cleaning jewelry and stainless steel appliances. Just spray on and wipe off. Shake well before use.
(pink)
Top Wax is a premium AMS certified paint and glass wax. It will Remove Black Streaks but for really bad streaking use the Metal Wax Polish first. (see the above instructions) Using a foam applicator pad, spread one coat on painted trailers, automotive paint, aircraft, vinyl decals, gel coated fiberglass boats, and auto/home/industrial glass. Wipe off with a clean microfiber towel leaving behind its crystal clear UV protection. Streak free and easy to use. Airplane and marine approved.
Use Top Wax on glass and plastic ( especially horse trailer and RV windows and frames) for a clean and protected finish. It will make them look new again.
(white)
DO NOT POLISH HOT METAL OR UNDER DIRECT SUNLIGHT
WEAR GLOVES WHEN USING THIS PRODUCT
THIS PRODUCT IS NOT COMPATIBLE WITH OTHER BRANDS
USE ONLY CLEAN POLISHING TOWELS
Metal Wax Polishing Gel is aero space certified AMS1650 C Type 2 & aircraft approved with spec numbers Douglas Aircraft CSD #1 Boeing cert numbers D6-17487 rev. P AMS1650 C Type 2
S M I - 05APR481
Top Wax Polish is aircraft certified with spec numbers CSD#1 and Boeing aircraft D6-17487 Rev,1 AMS1650 B type 1 and 2.
Quick Shine Liquid Metal Polish is aero space certified AMS1650 C Type 2 & aircraft approved with spec numbers Douglas Aircraft CSD #1 Boeing cert numbers D6-17487 rev. P AMS1650 C Type 2
S M I - 05APR481
See our new site for project photo and video: www.jmtdistribution.com
Questions? Please call!
Support hot line: 770-475-9295
Email: jmtdistribution@aol.com